Actron CP7529 Servisní příručka

CP7527 INDUCTIVECP7528 ADVANCECP7529 DIGITALTIMING LIGHTINSTRUCTIONSActron, is a Business Unit of SPX Corporation.

TDCUDC 1-616NOP 1-6OA36100DC1010IMPORTANT5. Locate the Timing Marks on the Engine· The Digital Timing Light is equipped witha flashlight feature. Pres

MEASURING ENGINE RPM(Digital Timing Light Only)1. Press and Release Button Until RPM Indicator Lights.If engine is not running or #1 spark plug is n

MEASURING INITIAL TIMING1. Follow preparation list for checkingtiming in vehicle service manual.2. Start engine and warm to operatingtemperature.3.

ADVANCE TIMING LIGHT1. Press and hold down button.2. View timing marks. Turn advance knob untilmoving mark is aligned with stationary 0 degree

SETTING INITIAL TIMINGINDUCTIVE TIMING LIGHT1. Press and hold down button.2. Loosen distributor hold down bolt and turndistributor as necessary un

3. View timing marks. Loosen distributor hold down bolt and turndistributor until moving mark is aligned with stationary 0 degreemark.4. Tighten d

CHECKING & MEASURINGCENTRIFUGAL ADVANCEINDUCTIVE TIMING LIGHT1. Leave distributor vacuum line disconnectedand plugged.2. Press and hold down but

ADVANCE TIMING LIGHT1. At distributor, leave vacuum line disconnected and plugged.2. Press and hold down button. View timing marks. Turn advancek

DIGITAL TIMING LIGHT1. At distributor, leave vacuum line disconnected and plugged.2. Push and buttons until moving mark is aligned with thestation

LEFT BLANK ON PURPOSE18

1TABLE OF CONTENTSSAFETY PRECAUTIONS ... 2TIMING LIGHTS...

MEASURING VACUUM ADVANCEChecking the vacuum advance mechanism requires a vacuum pump withgauge in addition to the timing light.INDUCTIVE TIMING LIGHT1

ADVANCE TIMING LIGHT1. At distributor, leave vacuum line disconnected and plugged. Connectvacuum pump to distributor.2. Increase engine speed to RPM s

DIGITAL TIMING LIGHT1. At distributor, leave vacuum line disconnected and plugged. Connectvacuum pump to distributor.2. Increase engine speed to RPM

DISCONNECTING TIMING LIGHT1. Turn Vehicle OFF.Disconnecting cables with vehicle engine running could resultin serious injury.2. At distributor, unplug

TROUBLESHOOTING AND CARETiming Light Flashes Randomly1. Clean Inductive Pickup ClampInside Surfaces with Soft ClothDo not allow tool to touchexhaust m

2. Slide Inductive Pickup Clamp To new spot on #1 spark plug wire3. Turn Inductive Pickup Over To opposite direction on #1 sparkplug wire4. Replace

© 2005 SPX Corporation All Rights Reserved.FULL ONE (1) YEAR WARRANTYSPX Corporation, 15825 Industrial Parkway, Cleveland, Ohio 44135, warrants tothe

SAFETY PRECAUTIONSFor safety reasons, read this manual thoroughly before operating Timing Light.Always refer to and follow safety messages and test pr

3SAFETY INSTRUCTIONSVentilation Operate vehicle in ventilated area.Moving Parts Remove Jewelry Do Not Wear Loose Clothing Tie Up Long Hair Keep H

Hot Surfaces Avoid Contact With: Exhaust Manifolds Pipes Radiator Mufflers (catalytic converters)Battery Do Not Lay Tools on Battery Do Not Tou

162/4CycleRPMAdv 7 8 11 14 12 9 13 10 14TIMING LIGHTS 16156CP7529DIGITALCP7528ADVANCECP7527INDUCTIVE5

1. Timing Light2. Lens3. Inductive Pickup Clamp4. RED Clip5. BLACK Clip6. 4-digit LED Display7. 2 Cycle Mode Indicator8. 4 Cycle Mode Indicator9. RPM

IMPORTANT1. Turn Vehicle OFF.Connecting cables with engine running could result in seriousinjury.2. At distributor, disconnect and plug vacuum line.3.

IMPORTANT4. Connect RED and BLACK Battery Clips on Negative Ground ElectricalSystems.· Connect RED to positive (+) battery post.· Connect BLACK to eng